#ifndef BCU_DB_ADDR_LINUX_H_ #define BCU_DB_ADDR_LINUX_H_ #include "bmser_db_control_db.h" typedef enum { BMS_DB_DEV_TOTAL, // 堆 BMS_DB_DEV_MASTER, // 簇 BMS_DB_DEV_ID_BUTT = BMS_DB_DEV_MASTER + BMS_CFG_ROCKSNUM_MAX // 最大簇数末尾 }BMS_DB_DEV_TYPE_ENUM; /* -------------------------------主控控制信息DB-------------------------- */ typedef enum { BMS_CTRL_SYSTEM_RESET = 0x0000, /*复位*/ BMS_CTRL_EEPROM_RESET, /*重置EEPROM值*/ BMS_CTRL_START_AGING_TEST, /*启动老化测试*/ BMS_CTRL_PCS_COMMAND, /*PCS控制指令*/ BMS_CTRL_NEGETIVE_CONTACTOR_SWITCH, /*强制下电指令*/ BMS_CTRL_LED_RED_ERR_SWITCH, /*告警红灯开关*/ BMS_CTRL_FAN_SWITCH, /*风扇供电开关*/ BMS_CTRL_LED_GREEN_NORMAL_SWITCH, /*正常绿灯开关*/ BMS_CTRL_ERR_CODE_ENABLE, /*错误码使能*/ BMS_CTRL_RESET_SLAVE_ID_ENABLE, /*重置从控唯一编号使能*/ BMS_CTRL_GROUP_BALANCE_STATE, /*组间均衡状态*/ BMS_CTRL_SAMPLE_CURRENT_MODE, /*采集电流类型*/ BMS_CTRL_POWER_OFF_MODE, /*主控下电使能*/ BMS_CTRL_SET_IO_ID, /*IO ID */ BMS_CTRL_SET_IO_STATE, /*配置IO 状态*/ BMS_CTRL_HVIL_OUT_MODE, /*高压互锁输出信号模式*/ BMS_CTRL_START_INSULATION_SAMPLE, /*启动绝缘采样*/ BMS_CTRL_PREPOWER_STATE, /*预充控制*/ BMS_CTRL_PARA_SET_MAINCTRL_INDEX, /*设置主控地址*/ BMS_CTRL_PARA_BOXBALANCE_TOTAL_SWITCH, /*组间均衡功能总开关*/ BMS_CTRL_PARA_ACTIVE_BALANCE_TOTAL_SWITCH, /*主动均衡功能总开关*/ BMS_CTRL_FEATURE_CONFIGURATION, /*功能配置*/ BMS_CTRL_FULL_EMPTY_RECOVER_CAP_AH, /* 充满放空恢复容量：Ah */ BMS_CTRL_FULL_EMPTY_PREPOWER_MAX_TIME, /* 充满或者放空时的预充最大时间：min */ BMS_CTRL_NOCHG_RECOVER_MAX_TIME, /* 禁充恢复所需最大时间（无需放电）:Hour */ BMS_CTRL_SOC_START_TIME_SMOOTH, /* 启动SOC时间平滑 */ BMS_CTRL_SOH_CALIB_ENABLE, /*SOH校准开关*/ BMS_CTRL_FAN_FORCE_CTRL, /* 风扇强控，由于BMS_CTRL_FAN_SWITCH定义与主控冲突，故新增一个 */ BMS_CTRL_MAXBAT_SOC_VALUE, /*最大单体SOC*/ BMS_CTRL_MINBAT_SOC_VALUE, /*最小单体SOC*/ BMS_CTRL_MAXMINBAT_SOC_DIFFER, /*最大最小单体SOC差值*/ BMS_CTRL_MAXBAT_Q, /*上一次校准最大单体置信度*/ BMS_CTRL_MINBAT_Q, /*上一次校准最小单体置信度*/ BMS_CTRL_IO_MODE_CONFIG, /* IO模式配置 */ BMS_CTRL_SET_STABLE_BALANCE_TIME, /*配置稳态均衡的时间*/ BMS_CTRL_BAU_TIME_HIGH, /*总控时间高位 */ BMS_CTRL_BAU_TIME_LOW, /*总控时间低位*/ BMS_CTRL_NTC_TEMP_REPLACE_ENABLE, /*温度替换开关*/ BMS_CTRL_FULL_CALIB_MIN_AVE_VOL, /* 充满校准最小平均电压 mV */ BMS_CTRL_EMPTY_CALIB_MAX_AVE_VOL, /* 放空校准最大平均电压 mV */ BMS_CTRL_FULL_EMPTY_CALIB_MAX_VOL_DIFF, /* 充满放空校准压差 mV */ BMS_CTRL_SOC_DECAY_POWER, /* SOC损耗功率*/ BMS_CTRL_CLEAR_ALL_RACK_CUT_EVENT, /* 一键清除断接触器异常事件 */ BMS_CTRL_PACK_SAFETY_TEST_ENABLE, /* 功能安全认证测试开关 */ BMS_CTRL_START_OCV_ADJUST, /* 启动一次OCV校准 */ BMS_CTRL_BAT_VOLT_SAMPLE_PERIOD, /* 电压采样周期配置 */ BMS_CTRL_BAT_TEMP_SAMPLE_PERIOD, /* 温度采样周期配置 */ BMS_CTRL_CLEAR_RESET_ALARM_1, /* 清除复归告警1 */ BMS_CTRL_CLEAR_RESET_ALARM_2, /* 清除复归告警2 */ BMS_CTRL_PARA_SUBOBJ_ID_BUTT }BMS_CTRL_PARA_SUBOBJ_ID_ENUM; /* -------------------------------主控配置信息DB-------------------------- */ typedef enum { BMS_CFG_INNER_SOC_VALUE = 0x0040, /*内部SOC值*/ BMS_CFG_SOH_OFFSET_VALUE, /*SOH偏移量*/ BMS_CFG_MAX_CAPACITY_VALUE, /*电池最大容量值*/ BMS_CFG_BOX_BALANCE_WORK_TIME, /*箱间均衡工作时间*/ BMS_CFG_BOX_BALANCE_SLEEP_TIME, /*箱间均衡间歇时间*/ BMS_CFG_CALIB_INDEX, /*校准索引*/ BMS_CFG_CALIB_VALUE, /*校准值*/ BMS_CFG_BALANCE_START_VOL_LIMIT, /*均衡开启电压*/ BMS_CFG_BALANCE_START_VOL_DIFF_LIMIT, /*均衡开启压差*/ BMS_CFG_BALANCE_BAT_VOL_OVER, /*均衡单体电压过高*/ BMS_CFG_BALANCE_BAT_VOL_UNDER, /*均衡单体电压过低*/ BMS_CFG_ACTIVE_CHECK_AUTO_VOL_DIFF_LIMIT, /*主动均衡检测Auto压差阈值 N*/ BMS_CFG_BALANCE_INNER_TEMP_HIGH, /*均衡温度过高*/ BMS_CFG_TIME_SMOOTH_MAX_TIME, /* 时间平滑最大追随时间 0.1S */ BMS_CFG_BALANCE_BAT_VOL_DIFF, /*均衡单体压差过大*/ BMS_CFG_SYS_TIME_YEAR, /*系统时间年*/ BMS_CFG_SYS_TIME_MONTH, /*系统时间月*/ BMS_CFG_SYS_TIME_DAY, /*系统时间日*/ BMS_CFG_SYS_TIME_WEEK, /*系统时间周*/ BMS_CFG_SYS_TIME_HOUR, /*系统时间时*/ BMS_CFG_SYS_TIME_MINUTE, /*系统时间分*/ BMS_CFG_SYS_TIME_SECOND, /*系统时间秒*/ BMS_CFG_MAX_ENABLE_SLAVE_NUM, /*从控使能最大个数*/ BMS_CFG_BOX_BALANCE_WORK_VOL, /*箱间均衡工作最低电压*/ BMS_CFG_MAX_ENABLE_BATTERY_NUM_OF_SYSTEM, /*所有从控使能最大电池数量*/ BMS_CFG_MAX_ENABLE_ALL_TEMP_NUM, /*使能所有电池温度数*/ BMS_CFG_TIME_SMOOTH_DEST_SOC_FULL, /* 充满时间平滑SOC目标 ‰ */ BMS_CFG_TIME_SMOOTH_DEST_SOC_EMPTY, /* 放空时间平滑SOC目标 ‰ */ BMS_CFG_TIME_SMOOTH_START_VOL_FULL, /* 充满时间平滑起始电压 mV */ BMS_CFG_TIME_SMOOTH_START_VOL_EMPTY, /* 放空时间平滑起始电压 mV */ BMS_CFG_ACTIVE_START_AVG_VOL_LIMIT, /*主动均衡模块开启平均电压*/ BMS_CFG_ACTIVE_END_VOL_DIFF_LIMIT, /*主动均衡模块停止极差*/ BMS_CFG_BOX_BALANCE_SATART_LIMIT, /*箱间均衡开启压差门限*/ BMS_CFG_BOX_BALANCE_END_LIMIT, /*箱间均衡关闭压差门限*/ BMS_CFG_ACTIVE_CHECK_VOL_DIFF_LIMIT, /*主动均衡检测压差阈值 M*/ BMS_CFG_ACTIVE_MAX_WORK_NUM, /*主动均衡发热量控制系数*/ BMS_CFG_ACTIVE_LOG_INFO_INDEX, /*主动均衡测试数据ID*/ BMS_CFG_ACTIVE_LOG_INFO_DATA, /*主动均衡测试数据内容*/ BMS_CFG_ACTIVE_FORCE_CTRL_STATE, /*主动均衡强控状态*/ BMS_CFG_PREPOWER_VOL_END_DIFF_VALUE, /*预充结束压差*/ BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_VOL_1, /*充电末端限流电压*/ BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_VOL_2, BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_VOL_3, BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_VOL_1, /*放电末端限流电压*/ BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_VOL_2, BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_VOL_3, BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_RATIO_1, /*充电末端限流电流比例*/ BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_RATIO_2, BMS_CFG_CHARGE_TAIL_LIMIT_CURRENT_RATIO_3, BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_RATIO_1, /*放电末端限流电流比例*/ BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_RATIO_2, BMS_CFG_DISCHARGE_TAIL_LIMIT_CURRENT_RATIO_3, BMS_CFG_CHARGE_MAX_CURRENT_LIMIT, /*最大限流门限*/ BMS_CFG_DISCHARGE_MAX_CURRENT_LIMIT, BMS_CFG_ADD_CHG_CELL_VOL_LIMIT, BMS_CFG_ADD_CHG_CURRENT_LIMIT, BMS_CFG_ADD_CHG_IDLE_DAY_LIMIT, BMS_CFG_FIRST_CHAIN_SAMPLE_CHIP_NUM, /*第一条菊花链使能的芯片数*/ BMS_CFG_SECOND_CHAIN_SAMPLE_CHIP_NUM, /*第二条菊花链使能的芯片数*/ BMS_CFG_ENABLE_SAMPLE_VOL_NUM_PER_CHIP, /*每个采样芯片使能采样数量*/ BMS_CFG_ENABLE_SAMPLE_VOL_NUM_LAST_CHIP, /*最后一个采样芯片使能采样数量*/ BMS_CFG_FAN_WORK_TEMP, /*风扇开启温度*/ BMS_CFG_FAN_STOP_TEMP, /*风扇断开温度*/ BMS_CFG_BALANCE_BAT_VOL_LOWEST, /*均衡单体电压极低*/ BMS_CFG_PARA_SUBOBJ_ID_BUTT }BMS_CFG_PARA_SUBOBJ_ID_ENUM; /* -------------------------------主控概要信息DB-------------------------- */ typedef enum { BMS_SUMMARY_PREPOWER_STAGE = 0x0080, /*预充电阶段*/ BMS_SUMMARY_SYSTEM_STATE, /*系统状态*/ BMS_SUMMARY_RECEIVE_SLAVE_CFG_INFO_STATE, /*接收配置信息状态*/ BMS_SUMMARY_RECEIVE_SLAVE_INFO_STATE_HIGH, /*接收从控信息状态高 (菊花链1错误芯片编号)*/ BMS_SUMMARY_RECEIVE_SLAVE_INFO_STATE_LOW, /*接收从控信息状态低 (菊花链2错误芯片编号)*/ BMS_SUMMARY_PREPOWER_FAIL_REASON, /*预充失败原因*/ BMS_SUMMARY_SLAVE_CALCULATE_TOTAL_VOL, /*从控总压累加和*/ BMS_SUMMARY_TOTAL_VOL_DIFF_VALUE, /*总压压差*/ BMS_SUMMARY_PREPOWER_TOTAL_VOL, /*预充总压*/ BMS_SUMMARY_MAX_SINGLE_VOLTAGE_VALUE, /*最大单体电压*/ BMS_SUMMARY_MAX_SINGLE_VOLTAGE_NUM, /*最大单体电压编号*/ BMS_SUMMARY_MAX_SINGLE_VOLTAGE_PACK_ID, /*最高单体所在的模组*/ BMS_SUMMARY_MAX_SINGLE_VOLTAGE_PACK_NUM, /*最高单体在所在的模组中的位置*/ BMS_SUMMARY_MIN_SINGLE_VOLTAGE_VALUE, /*最小单体电压*/ BMS_SUMMARY_MIN_SINGLE_VOLTAGE_NUM, /*最小单体电压编号*/ BMS_SUMMARY_MIN_SINGLE_VOLTAGE_PACK_ID, /*最低单体所在的模组*/ BMS_SUMMARY_MIN_SINGLE_VOLTAGE_PACK_NUM, /*最低单体在所在的模组中的位置*/ BMS_SUMMARY_MAX_SINGLE_VOLTAGE_DIFF_VALUE, /*电池单体电压最高最低差值*/ BMS_SUMMARY_CELL_AVERAGE_VOL_VALUE, /*单体平均电压*/ BMS_SUMMARY_MAX_SINGLE_TEMP_VALUE, /*最大温度*/ BMS_SUMMARY_MAX_SINGLE_TEMP_NUM, /*最大温度编号*/ BMS_SUMMARY_MAX_SINGLE_TEMP_PACK_ID, /*最高温度所在的模组*/ BMS_SUMMARY_MAX_SINGLE_TEMP_PACK_NUM, /*最高温度在所在的模组中的位置*/ BMS_SUMMARY_MIN_SINGLE_TEMP_VALUE, /*最小温度*/ BMS_SUMMARY_MIN_SINGLE_TEMP_NUM, /*最小温度编号*/ BMS_SUMMARY_MIN_SINGLE_TEMP_PACK_ID, /*最低温度所在的模组*/ BMS_SUMMARY_MIN_SINGLE_TEMP_PACK_NUM, /*最低温度在所在的模组中的位置*/ BMS_SUMMARY_ENVIRONMENT_TEMP, /*环境温度*/ BMS_SUMMARY_MAX_ANODE_TEMP_VALUE, /*最大极柱温度*/ BMS_SUMMARY_MAX_ANODE_TEMP_VALUE_ID, /*最大极柱温度编号*/ BMS_SUMMARY_MAX_ACCEPTABLE_CHARGE_CURRENT, /*显示可接受最大充电电流 0.1A*/ BMS_SUMMARY_MAX_ACCEPTABLE_DISCHARGE_CURRENT, /*显示可接受最大放电电流 0.1A*/ BMS_SUMMARY_DISPLAY_SOC_VALUE, /*显示SOC*/ BMS_SUMMARY_SOH, /*soh值*/ BMS_SUMMARY_KM_RELAY_USED_LIFE_TIMES, /*总正接触器使用次数*/ BMS_SUMMARY_KM_RELAY_WEIGHTED_LIFE_TIMES, /*总正接触器加权重使用次数*/ BMS_SUMMARY_KP_RELAY_USED_LIFE_TIMES, /*预充接触器使用次数*/ BMS_SUMMARY_KP_RELAY_WEIGHTED_LIFE_TIMES, /*预充接触器加权重使用次数*/ BMS_SUMMARY_K__RELAY_USED_LIFE_TIMES, /*总负接触器使用次数*/ BMS_SUMMARY_K__RELAY_WEIGHTED_LIFE_TIMES, /*总负接触器加权重使用次数*/ BMS_SUMMARY_CHARGE_DISCHARGE_STATE, /*充放电状态(根据电流方向判断)*/ BMS_SUMMARY_MAX_PASSIVE_BALANCE_TEMP_NUM, /*最大均衡温度数量*/ BMS_SUMMARY_IS_NEED_ADD_CHARGE, /*是否需要补电*/ BMS_SUMMARY_DISTRIBUTE_STAGE, /*自动分配ID阶段*/ BMS_SUMMARY_CAN_1_BUS_OFF_TIMES, /*进入BUS OFF的时间次数*/ BMS_SUMMARY_CAN_2_BUS_OFF_TIMES, BMS_SUMMARY_MAX_TEMP_DIFF, /* 最大最小温差 */ BMS_SUMMARY_FULL_EMPTY_STATE, /*充满放空标志:bit0置1充满;bit1置1放空*/ BMS_SUMMARY_ACTIVE_TEMP_NUM, /*主动均衡温度数量*/ BMS_SUMMARY_ACTIVE_MODULE_NUM, /*主动均衡模块数量*/ BMS_SUMMARY_TOTAL_CAPACITY_VALUE, /*系统总容量*/ BMS_SUMMARY_ENABLE_CHARGE_ENERGY, /*可充电电量*/ BMS_SUMMARY_ENABLE_DISCHARGE_ENERGY, /*可放电电量*/ BMS_SUMMARY_RECENTLY_CHARGE_ENERGY, /*最近一次充电电量*/ BMS_SUMMARY_RECENTLY_DISCHARGE_ENERGY, /*最近一次放电电量*/ BMS_SUMMARY_ACCUMULATED_CHARGE_ENERGY_HIGH, /*累计充电电量*/ BMS_SUMMARY_ACCUMULATED_CHARGE_ENERGY_LOW, /*累计充电电量*/ BMS_SUMMARY_ACCUMULATED_DISCHARGE_ENERGY_HIGH, /*累计放电电量*/ BMS_SUMMARY_ACCUMULATED_DISCHARGE_ENERGY_LOW, /*累计放电电量*/ BMS_SUMMARY_ACCUMULATED_CHARGE_ENERGY_TODAY, /*当天累计充电电量 KWh*/ BMS_SUMMARY_ACCUMULATED_DISCHARGE_ENERGY_TODAY, /*当天累计放电电量 KWh*/ BMS_SUMMARY_REAL_MAX_ACCEPTABLE_CHARGE_CURRENT, /*最大充电电流能力 0.1A*/ BMS_SUMMARY_REAL_MAX_ACCEPTABLE_DISCHARGE_CURRENT, /*最大放电电流能力 0.1A*/ BMS_SUMMARY_INNER_SOC_VALUE, /*内部INNER SOC*/ BMS_SUMMARY_INFO_SUBOBJ_ID_BUTT }BMS_SUMMARY_INFO_SUBOBJ_ID_ENUM; /* -------------------------------主控采样信息DB-------------------------- */ typedef enum { BMS_SAMPLE_BATTERY_TOTAL_VOL = 0x00C0, /*电池总电压*/ BMS_SAMPLE_REALY_KP_VOL, /*继电器电压1*/ BMS_SAMPLE_REALY_TWO_VOL, /*继电器电压2*/ BMS_SAMPLE_REALY_THREE_VOL, /*继电器电压3*/ BMS_SAMPLE_REALY_FOUR_VOL, /*继电器电压4*/ BMS_SAMPLE_REALY_FIVE_VOL, /*继电器电压5*/ BMS_SAMPLE_SLAVE_ERR_INFO_1, /*从控错误信息1*/ BMS_SAMPLE_SLAVE_ERR_INFO_2, /*从控错误信息2*/ BMS_SAMPLE_TOTAL_CURRENT, /*系统总电流采集*/ BMS_SAMPLE_MAIN_CHIP_CURRENT, /*电流主采样芯片电流值*/ BMS_SAMPLE_SUB_CHIP_CURRENT, /*电流副采样芯片电流值*/ BMS_SAMPLE_INSULATION_RES, /*绝缘阻值*/ BMS_SAMPLE_POS_INSULATION_RES, /*正端绝缘阻值*/ BMS_SAMPLE_NEG_INSULATION_RES, /*负端绝缘阻值*/ BMS_SAMPLE_SUPPLY_POWER_VOL, /*供电采样电压*/ BMS_SAMPLE_RAW_SUPPLY_POWER_VOL, /*原始供电电压*/ BMS_SAMPLE_RAW_SHUNT_CURRENT, /*原始分流器总电流*/ BMS_SAMPLE_RAW_HALL1_CURRENT, /*原始Can霍尔采样电流值*/ BMS_SAMPLE_RAW_HALL2_CURRENT, /*原始电流/电压型霍尔采样电流值*/ BMS_SAMPLE_RAW_K1ON_K2ON_R2_VOL, /*总电压采样时K1K2闭合时R2的电压*/ BMS_SAMPLE_RAW_K1ON_K2ON_R3_VOL, /*总电压采样时K1K2闭合时R3的电压*/ BMS_SAMPLE_RAW_K1ON_K2OFF_R2_VOL, /*采集绝缘时K1闭合K2断开时R2的电压*/ BMS_SAMPLE_RAW_K1OFF_K2ON_R3_VOL, /*采集绝缘时K1断开K2闭合时R3的电压*/ BMS_SAMPLE_RAW_ANALOG_1_SAMPLE_VOL, /*模拟1采样adc值*/ BMS_SAMPLE_RAW_ANALOG_2_SAMPLE_VOL, /*模拟2采样adc值*/ BMS_SAMPLE_RAW_ANALOG_3_SAMPLE_VOL, /*模拟3采样adc值*/ BMS_SAMPLE_RAW_ANALOG_4_SAMPLE_VOL, /*模拟4采样adc值*/ BMS_SAMPLE_RAW_ANALOG_5_SAMPLE_VOL, /*模拟5采样adc值*/ BMS_SAMPLE_RAW_ANALOG_6_SAMPLE_VOL, /*模拟6采样adc值*/ BMS_SAMPLE_ANALOG_1_SAMPLE_TEMP, /*模拟1采样值*/ BMS_SAMPLE_ANALOG_2_SAMPLE_TEMP, /*模拟2采样值*/ BMS_SAMPLE_ANALOG_3_SAMPLE_TEMP, /*模拟3采样温度值*/ BMS_SAMPLE_ANALOG_4_SAMPLE_TEMP, /*模拟4采样温度值*/ BMS_SAMPLE_ANALOG_5_SAMPLE_TEMP, /*模拟5采样温度值*/ BMS_SAMPLE_ANALOG_6_SAMPLE_TEMP, /*模拟6采样温度值*/ BMS_SAMPLE_RAW_K3ON_K2ON_R2_VOL, /*总正接触器电压采样时K3K2闭合时R2的电压*/ BMS_SAMPLE_RAW_K3ON_K2ON_R3_VOL, /*总正接触器电压采样时K3K2闭合时R3的电压*/ BMS_SAMPLE_RAW_K__VOL, /*总负接触器原始电压采样*/ BMS_SAMPLE_RAW_K1ON_K4ON_R3_VOL, /*总负接触器电压采样时K1K4闭合时R3的电压*/ BMS_SAMPLE_RAW_K6ON_K2ON_R2_VOL, /*预留接触器电压采样时K6K2闭合时R2的电压*/ BMS_SAMPLE_RAW_K6ON_K2ON_R3_VOL, /*预留接触器电压采样时K6K2闭合时R3的电压*/ BMS_SAMPLE_MAX_HVBOX_TEMP, /*高压箱最高温度*/ BMS_SAMPLE_RAW_ANALOG_7_SAMPLE_VOL, /*模拟7采样adc值*/ BMS_SAMPLE_RAW_ANALOG_8_SAMPLE_VOL, /*模拟8采样adc值*/ BMS_SAMPLE_ANALOG_7_SAMPLE_TEMP, /*模拟7采样温度值*/ BMS_SAMPLE_ANALOG_8_SAMPLE_TEMP, /*模拟8采样温度值*/ BMS_SAMPLE_RAW_226_SAMPLE_VOL_1, /*电流型霍尔226采样电压原始值*/ BMS_SAMPLE_RAW_226_SAMPLE_VOL_2, /*分流器226采样电压原始值(预留)*/ BMS_SAMPLE_RAW_HALL_5V_SAMPLE_VOL, /*电流型霍尔5V电压原始值*/ BMS_SAMPLE_RAW_HALL_12V_SAMPLE_VOL, /*电流型霍尔12V电压原始值*/ BMS_SAMPLE_RAW_ADC_INNER_REF_SAMPLE_VOL, /* MCU ADC内部基准采样值 */ BMS_SAMPLE_HVB_TEMP_1, /* 高压箱温度1 */ BMS_SAMPLE_HVB_TEMP_2, /* 高压箱温度2 */ BMS_SAMPLE_HVB_TEMP_3, /* 高压箱温度3 */ BMS_SAMPLE_HVB_TEMP_4, /* 高压箱温度4 */ BMS_SAMPLE_RAW_239_0_SAMPLE_SHUNT_VOL, /*INA239_0采样电流原始电压值*/ BMS_SAMPLE_RAW_239_0_SAMPLE_TEMP_VOL, /*INA239_0采样温度原始电压值*/ BMS_SAMPLE_RAW_239_1_SAMPLE_SHUNT_VOL, /*INA239_1采样电流原始电压值*/ BMS_SAMPLE_RAW_239_1_SAMPLE_K__VOL, /*INA239_1采样接触器负原始电压值*/ BMS_SAMPLE_HVIL_IN_SAMPLE, /*高压互锁采样*/ BMS_SAMPLE_IO0_WAKEUP_SAMPLE, /*唤醒IO0采样*/ BMS_SAMPLE_IO1_WAKEUP_SAMPLE, /*唤醒IO1采样*/ BMS_SAMPLE_INFO_SUBOBJ_ID_BUTT }BMS_SAMPLE_INFO_SUBOBJ_ID_ENUM; /* -------------------------------主控故障信息DB-------------------------- */ typedef enum { BMS_CRITICAL_STOP_INFO = 0x0100, BMS_CRITICAL_ALARM_INFO, BMS_CRITICAL_ALERT_INFO, BMS_CRITICAL_OTHER_ALARM_INFO, BMS_CRITICAL_RELAY_TOTAL_STATE, /*主控对外接触器总状态*/ BMS_CRITICAL_RELAY_KM_STATE, /*接触器KM状态*/ BMS_CRITICAL_RELAY_KP_STATE, /*接触器KP状态*/ BMS_CRITICAL_RELAY_K__STATE, /*接触器K_状态*/ BMS_CRITICAL_LED_RED_ERR_STATE, /*告警红灯状态*/ BMS_CRITICAL_LED_GREEN_STATE, /*绿灯状态*/ BMS_CRITICAL_ADS1147_0_STATE, /*目前用来存放MC33772的状态*/ BMS_CRITICAL_ADS1147_1_STATE, /*目前用来存放LTC6811的状态*/ BMS_CRITICAL_INA226_STATE, /*INA226告警状态*/ BMS_CRITICAL_ADC_STATE, /*ADC告警状态*/ BMS_CRITICAL_RTC_STATE, /*RTC时钟告警状态*/ BMS_CRITICAL_EXT_FLASH_STATE, /*extFlash自检状态*/ BMS_CRITICAL_EEPROM_STATE, /*EEP故障状态*/ BMS_CRITICAL_PACKPOS_RELAY_STATE, /*PACK正接触器检测状态*/ BMS_CRITICAL_CHG_RELAY_STATE, /*CHG接触器检测状态*/ BMS_CRITICAL_PACKNEG_RELAY_STATE, /*PACK负接触器检测状态*/ BMS_CRITICAL_OCV_ADJUST_STATE, /*OCV校准状态*/ BMS_CRITICAL_SLAVE_FAULT_STATE, /*从控故障状态*/ BMS_CRITICAL_CAN_BUS_1_STATE, /*CAN1通信状态*/ BMS_CRITICAL_CAN_BUS_2_STATE, /*CAN2通信状态*/ BMS_CRITICAL_SAFETY_SUMMARY, /*功能安全概要故障*/ BMS_CRITICAL_STABLE_BALANCE_ERROR_CODES, /*稳态均衡错误码*/ BMS_CRITICAL_BALANCER_ERROR_TYPE_HIGH, /*均衡错误类型高16位*/ BMS_CRITICAL_BALANCER_ERROR_TYPE_LOW, /*均衡错误类型低16位*/ BMS_CRITICAL_PASSIVE_BALANCE_FAULT_STATE_1, /*被动均衡故障状态1*/ BMS_CRITICAL_PASSIVE_BALANCE_FAULT_STATE_2, /*被动均衡故障状态2*/ BMS_CRITICAL_PASSIVE_BALANCE_FAULT_STATE_3, /*被动均衡故障状态3*/ BMS_CRITICAL_PASSIVE_BALANCE_FAULT_STATE_4, /*被动均衡故障状态4*/ BMS_CRITICAL_ACTIVE_BALANCE_FAULT_STATE_1, /*主动均衡故障状态1*/ BMS_CRITICAL_ACTIVE_BALANCE_FAULT_STATE_2, /*主动均衡故障状态2*/ BMS_CRITICAL_ACTIVE_BALANCE_FAULT_STATE_3, /*主动均衡故障状态3*/ BMS_CRITICAL_ACTIVE_BALANCE_FAULT_STATE_4, /*主动均衡故障状态4*/ BMS_CRITICAL_STOP_INFO_2, /*三级告警扩展*/ BMS_CRITICAL_ALARM_INFO_2, BMS_CRITICAL_ALERT_INFO_2, BMS_CRITICAL_NTC_FAULT_STATE_1, /*NTC故障状态1*/ BMS_CRITICAL_NTC_FAULT_STATE_2, /*NTC故障状态2*/ BMS_CRITICAL_NTC_FAULT_STATE_3, /*NTC故障状态3*/ BMS_CRITICAL_NTC_FAULT_STATE_4, /*NTC故障状态4*/ BMS_CRITICAL_NTC_FAULT_STATE_5, /*NTC故障状态5*/ BMS_CRITICAL_NTC_FAULT_STATE_6, /*NTC故障状态6*/ BMS_CRITICAL_NTC_FAULT_STATE_7, /*NTC故障状态7*/ BMS_CRITICAL_NTC_FAULT_STATE_8, /*NTC故障状态8*/ BMS_CRITICAL_EEP_WRITE_TIMES_PER_SEC, /*每秒钟写入eep的最大次数*/ BMS_CRITICAL_EEP_WRITE_TOTAL_TIMES_HIGH_16BIT, /*上电后eep写入次数高16位*/ BMS_CRITICAL_EEP_WRITE_TOTAL_TIMES_LOW_16BIT, /*上电后eep写入次数低16位*/ BMS_CRITICAL_INSULATE_FAULT_STATE, /*绝缘监测故障状态*/ BMS_CRITICAL_ALL_SLAVE_COMM_STATE_HIGH, /*所有从控的通信故障信息,1个bit代表一个从控*/ BMS_CRITICAL_ALL_SLAVE_COMM_STATE_LOW, /*所有从控的通信故障信息,1个bit代表一个从控*/ BMS_CRITICAL_RESET_REASON, BMS_CRITICAL_CLUSTER_PORT_STATE, /*簇端口检测状态,对外故障*/ BMS_CRITICAL_SYS_TICK_100MS_HIGH, BMS_CRITICAL_SYS_TICK_100MS_LOW, BMS_CRITICAL_EXT_STOP_INFO, /*总控用于对外显示的告警*/ BMS_CRITICAL_EXT_ALARM_INFO, BMS_CRITICAL_EXT_ALERT_INFO, BMS_CRITICAL_ALL_SLAVE_SUMMARY_FAULT_HIGHEST, /*所有从控的概要故障信息,1个bit代表一个从控，33-48*/ BMS_CRITICAL_ALL_SLAVE_SUMMARY_FAULT_HIGH, /*所有从控的概要故障信息,1个bit代表一个从控，17-32*/ BMS_CRITICAL_ALL_SLAVE_SUMMARY_FAULT_LOW, /*所有从控的概要故障信息,1个bit代表一个从控，1-16*/ BMS_CRITICAL_ALL_SLAVE_COMM_STATE_HIGHEST, /*所有从控的通信故障信息,1个bit代表一个从控*/ BMS_CRITICAL_STATE_SUBOBJ_ID_BUTT }BMS_CRITICAL_STATE_SUBOBJ_ID_ENUM; /* -------------------------------主控告警信息DB-------------------------- */ typedef enum { BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_CRITICAL = 0x0140, /*总电压过高*/ BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_ALARM, BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_WARN, BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_CRITICAL, /*总电压过低*/ BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_ALARM, BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_WARN, BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_CRITICAL, /*AD采样与从控上报总电压压差*/ BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_ALARM, BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_WARN, BMS_WARN_INSULATION_RES_LOWER_LOW_CRITICAL, /*绝缘阻值过低*/ BMS_WARN_INSULATION_RES_LOWER_LOW_ALARM, BMS_WARN_INSULATION_RES_LOWER_LOW_WARN, BMS_WARN_SOC_LOWER_LOW_CRITICAL, /*SOC过低*/ BMS_WARN_SOC_LOWER_LOW_ALARM, BMS_WARN_SOC_LOWER_LOW_WARN, BMS_WARN_SOC_OVER_HIGH_CRITICAL, /*SOC过高*/ BMS_WARN_SOC_OVER_HIGH_ALARM, BMS_WARN_SOC_OVER_HIGH_WARN, BMS_WARN_SOH_LOWER_LOW_CRITICAL, /*SOH过低*/ BMS_WARN_SOH_LOWER_LOW_ALARM, BMS_WARN_SOH_LOWER_LOW_WARN, BMS_WARN_HVBOX_TEMP_OVER_HIGH_CRITICAL, /*高压箱温度过高*/ BMS_WARN_HVBOX_TEMP_OVER_HIGH_ALARM, BMS_WARN_HVBOX_TEMP_OVER_HIGH_WARN, BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_CRITICAL, /*电池组单体电压过高*/ BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_ALARM, BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_WARN, BMS_WARN_SINGLE_BAT_VOL_HIGHEST_HIGH_CRITICAL, /*单体电压极高*/ BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_CRITICAL, /*电池组单体电压过低*/ BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_ALARM, BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_WARN, BMS_WARN_SINGLE_BAT_VOL_LOWEST_LOW_CRITICAL, /*单体电压极低*/ BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_CRITICAL, /*电池组单体电池电压差*/ BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_ALARM, BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_WARN, BMS_WARN_BAT_TEMP_OVER_HIGH_CRITICAL, /*电池组温度过高*/ BMS_WARN_BAT_TEMP_OVER_HIGH_ALARM, BMS_WARN_BAT_TEMP_OVER_HIGH_WARN, BMS_WARN_BAT_TEMP_LOWER_LOW_CRITICAL, /*电池组温度过低*/ BMS_WARN_BAT_TEMP_LOWER_LOW_ALARM, BMS_WARN_BAT_TEMP_LOWER_LOW_WARN, BMS_WARN_BAT_TEMP_OVER_DIFFER_CRITICAL, /*电池组温差*/ BMS_WARN_BAT_TEMP_OVER_DIFFER_ALARM, BMS_WARN_BAT_TEMP_OVER_DIFFER_WARN, BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_CRITICAL, /*电池温升过高*/ BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_ALARM, BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_WARN, BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_CRITICAL, /*电池组充电温度过高*/ BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_ALARM, BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_WARN, BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_CRITICAL, /*电池组充电温度过低*/ BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_ALARM, BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_WARN, BMS_WARN_POLARITY_TEMP_OVER_HIGH_CRITICAL, /*极耳温度过高*/ BMS_WARN_POLARITY_TEMP_OVER_HIGH_ALARM, BMS_WARN_POLARITY_TEMP_OVER_HIGH_WARN, BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_CRITICAL, /*放电电流过大*/ BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_ALARM, BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_WARN, BMS_WARN_CHARGE_CURRENT_OVER_HIGH_CRITICAL, /*充电电流过大*/ BMS_WARN_CHARGE_CURRENT_OVER_HIGH_ALARM, BMS_WARN_CHARGE_CURRENT_OVER_HIGH_WARN, BMS_WARN_PARA_SUBOBJ_ID_BUTT }BMS_WARN_PARA_SUBOBJ_ID_ENUM; /*告警相关门限 加一个预处理告警宏*/ /* -------------------------------主控告警恢复信息DB-------------------------- */ typedef enum { BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_CRITICAL_RECOVER = 0x0180,/*总电压过高*/ BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_ALARM_RECOVER, BMS_WARN_TOTAL_BAT_VOL_OVER_HIGH_WARN_RECOVER, BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_CRITICAL_RECOVER, /*总电压过低*/ BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_ALARM_RECOVER, BMS_WARN_TOTAL_BAT_VOL_LOWER_LOW_WARN_RECOVER, BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_CRITICAL_RECOVER, /*AD采样与从控上报总电压压差*/ BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_ALARM_RECOVER, BMS_WARN_TOTAL_BAT_VOL_OVER_DIFFER_WARN_RECOVER, BMS_WARN_INSULATION_RES_LOWER_LOW_CRITICAL_RECOVER, /*绝缘阻值过低*/ BMS_WARN_INSULATION_RES_LOWER_LOW_ALARM_RECOVER, BMS_WARN_INSULATION_RES_LOWER_LOW_WARN_RECOVER, BMS_WARN_SOC_LOWER_LOW_CRITICAL_RECOVER, /*SOC过低*/ BMS_WARN_SOC_LOWER_LOW_ALARM_RECOVER, BMS_WARN_SOC_LOWER_LOW_WARN_RECOVER, BMS_WARN_SOC_OVER_HIGH_CRITICAL_RECOVER, /*SOC过高*/ BMS_WARN_SOC_OVER_HIGH_ALARM_RECOVER, BMS_WARN_SOC_OVER_HIGH_WARN_RECOVER, BMS_WARN_SOH_LOWER_LOW_CRITICAL_RECOVER, /*SOH过低*/ BMS_WARN_SOH_LOWER_LOW_ALARM_RECOVER, BMS_WARN_SOH_LOWER_LOW_WARN_RECOVER, BMS_WARN_HVBOX_TEMP_OVER_HIGH_CRITICAL_RECOVER, /*高压箱温度过高*/ BMS_WARN_HVBOX_TEMP_OVER_HIGH_ALARM_RECOVER, BMS_WARN_HVBOX_TEMP_OVER_HIGH_WARN_RECOVER, BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_CRITICAL_RECOVER, /*电池组单体电压过高*/ BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_ALARM_RECOVER, BMS_WARN_SINGLE_BAT_VOL_OVER_HIGH_WARN_RECOVER, BMS_WARN_SINGLE_BAT_VOL_HIGHEST_HIGH_CRITICAL_RECOVER, /*单体电压极高*/ BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_CRITICAL_RECOVER, /*电池组单体电压过低*/ BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_ALARM_RECOVER, BMS_WARN_SINGLE_BAT_VOL_LOWER_LOW_WARN_RECOVER, BMS_WARN_SINGLE_BAT_VOL_LOWEST_LOW_CRITICAL_RECOVER, /*单体电压极低*/ BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_CRITICAL_RECOVER, /*电池组单体电池电压差*/ BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_ALARM_RECOVER, BMS_WARN_SINGLE_BAT_VOL_OVER_DIFFER_WARN_RECOVER, BMS_WARN_BAT_TEMP_OVER_HIGH_CRITICAL_RECOVER, /*电池组温度过高*/ BMS_WARN_BAT_TEMP_OVER_HIGH_ALARM_RECOVER, BMS_WARN_BAT_TEMP_OVER_HIGH_WARN_RECOVER, BMS_WARN_BAT_TEMP_LOWER_LOW_CRITICAL_RECOVER, /*电池组温度过低*/ BMS_WARN_BAT_TEMP_LOWER_LOW_ALARM_RECOVER, BMS_WARN_BAT_TEMP_LOWER_LOW_WARN_RECOVER, BMS_WARN_BAT_TEMP_OVER_DIFFER_CRITICAL_RECOVER, /*电池组温差*/ BMS_WARN_BAT_TEMP_OVER_DIFFER_ALARM_RECOVER, BMS_WARN_BAT_TEMP_OVER_DIFFER_WARN_RECOVER, BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_CRITICAL_RECOVER, /*电池温升过高*/ BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_ALARM_RECOVER, BMS_WARN_BAT_TEMP_RISE_OVER_HIGH_WARN_RECOVER, BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_CRITICAL_RECOVER, /*电池组充电温度过高*/ BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_ALARM_RECOVER, BMS_WARN_BAT_CHARGE_TEMP_OVER_HIGH_WARN_RECOVER, BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_CRITICAL_RECOVER, /*电池组充电温度过低*/ BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_ALARM_RECOVER, BMS_WARN_BAT_CHARGE_TEMP_LOWER_LOW_WARN_RECOVER, BMS_WARN_POLARITY_TEMP_OVER_HIGH_CRITICAL_RECOVER, /*极耳温度过高*/ BMS_WARN_POLARITY_TEMP_OVER_HIGH_ALARM_RECOVER, BMS_WARN_POLARITY_TEMP_OVER_HIGH_WARN_RECOVER, BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_CRITICAL_RECOVER, /*放电电流过大*/ BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_ALARM_RECOVER, BMS_WARN_DISCHARGE_CURRENT_OVER_HIGH_WARN_RECOVER, BMS_WARN_CHARGE_CURRENT_OVER_HIGH_CRITICAL_RECOVER, /*充电电流过大*/ BMS_WARN_CHARGE_CURRENT_OVER_HIGH_ALARM_RECOVER, BMS_WARN_CHARGE_CURRENT_OVER_HIGH_WARN_RECOVER, BMS_WARN_PARA_RECOVER_SUBOBJ_ID_BUTT }BMS_WARN_PARA_RECOVER_SUBOBJ_ID_ENUM; /*告警恢复相关门限*/ /* -------------------------------主控预留信息DB-------------------------- */ typedef enum { BMS_RESVER_ACTIVE_TEST_ERR_NUM = 0x0A00, /*主动均衡模块错误编号*/ BMS_RESVER_PASSIVE_TEST_ERR_NUM, /*被动均衡模块错误编号*/ BMS_RESVER_ACTIVE_TEST_MAX_BUCK_VOL, /*主动均衡最大BUCK电压*/ BMS_RESVER_ACTIVE_TEST_MAX_BUCK_VOL_ID, /*主动均衡最大BUCK电压编号*/ BMS_RESVER_ACTIVE_TEST_MIN_BUCK_VOL, /*主动均衡最小BUCK电压*/ BMS_RESVER_ACTIVE_TEST_MIN_BUCK_VOL_ID, /*主动均衡最小BUCK电压编号*/ BMS_RESVER_ACTIVE_TEST_MAX_BOOST_VOL, /*主动均衡最大BOOST电压*/ BMS_RESVER_ACTIVE_TEST_MAX_BOOST_VOL_ID, /*主动均衡最大BOOST电压编号*/ BMS_RESVER_ACTIVE_TEST_MIN_BOOST_VOL, /*主动均衡最小BOOST电压*/ BMS_RESVER_ACTIVE_TEST_MIN_BOOST_VOL_ID, /*主动均衡最小BOOST电压编号*/ BMS_RESVER_FAN_FAULT_STATE, /*风扇故障状态*/ BMS_RESVER_ALL_BFU_COMM_STATE_HIGHEST, /*所有BFU从控的通信故障信息,1个bit代表一个从控*/ BMS_RESVER_ALL_BFU_COMM_STATE_HIGH, /*所有BFU从控的通信故障信息,1个bit代表一个从控*/ BMS_RESVER_ALL_BFU_COMM_STATE_LOW, /*所有BFU从控的通信故障信息,1个bit代表一个从控*/ BMS_RESVER_DISTRIBUTE_SLAVE_ID_ERR_NO, /*自动分配从控ID错误的从控编号*/ BMS_RESVER_CLUSTER_RESISTANCE, /*电池簇内阻*/ BMS_RESVER_RES_SOC_RECODE, /*记录电池内阻时的SOC*/ BMS_RESVER_RES_TEMP_RECODE, /*记录电池内阻时的温度*/ BMS_RESVER_RES_VOLT_1_RECODE, /*电池内阻时第一次总压采样*/ BMS_RESVER_RES_VOLT_2_RECODE, /*电池内阻时第二次总压采样*/ BMS_RESVER_RES_CURR_1_RECODE, /*电池内阻时第一次电流采样*/ BMS_RESVER_RES_CURR_2_RECODE, /*电池内阻时第二次电流采样*/ BMS_RESVER_NTC_ALERT_STATE, /*NTC故障信息*/ BMS_RESVER_OTHER_ALARM_INFO, /*其它二级告警*/ BMS_RESVER_OTHER_ALERT_INFO, /*其它一级告警*/ BMS_RESVER_ACCUMULATED_CHARGE_ENERGY_MONTH, /*当月累计充电电量 KWh*/ BMS_RESVER_ACCUMULATED_DISCHARGE_ENERGY_MONTH, /*当月累计放电电量 KWh*/ BMS_RESVER_AFE_SLEEP_EN, /*AFE休眠使能*/ BMS_RESVER_MAX_BAT_TEMP_RISE, /*簇最高单体温升*/ BMS_RESVER_MAX_BAT_TEMP_RISE_BMU_NUM, /*簇最高单体温升电池包编号*/ BMS_RESVER_MAX_BAT_TEMP_RISE_NUM, /*簇最高单体温升电池包中单体温度编号*/ BMS_RESVER_SAMPLE_LINE_FAULT_STATE_1, /*采样线故障状态1*/ BMS_RESVER_SAMPLE_LINE_FAULT_STATE_2, /*采样线故障状态2*/ BMS_RESVER_SAMPLE_LINE_FAULT_STATE_3, /*采样线故障状态3*/ BMS_RESVER_SAMPLE_LINE_FAULT_STATE_4, /*采样线故障状态4*/ BMS_RESVER_MAX_BAT_TEMP_RISE_NUM_OVERALL, /*簇最高单体温升所有单体中的编号*/ BMS_RESVER_FAN_CTRL_STATE_1, /* 1-16bfu风扇控制状态 */ BMS_RESVER_FAN_CTRL_STATE_2, /* 17-32bfu风扇控制状态 */ BMS_RESVER_FAN_CTRL_STATE_3, /* 33-48bfu风扇控制状态 */ BMS_RESVER_FAN_FAULT_STATE_1, /* 1-16bfu风扇故障状态 */ BMS_RESVER_FAN_FAULT_STATE_2, /* 17-32bfu风扇故障状态 */ BMS_RESVER_FAN_FAULT_STATE_3, /* 33-48bfu风扇故障状态 */ BMS_RESVER_PACK_NUM, /*电池包数量*/ BMS_RESVER_ANODE_TEMP_NUM, /*极柱温度数量*/ BMS_RESVER_TEMP_NUM_PER_SLAVE, /*单个从控采集温度数量*/ BMS_RESVER_ACCUMULATED_CHARGE_ENERGY_YEAR_HIGH, /*当年累计充电电量 KWh*/ BMS_RESVER_ACCUMULATED_CHARGE_ENERGY_YEAR_LOW, /*当年累计充电电量 KWh*/ BMS_RESVER_ACCUMULATED_DISCHARGE_ENERGY_YEAR_HIGH, /*当年累计放电电量 KWh*/ BMS_RESVER_ACCUMULATED_DISCHARGE_ENERGY_YEAR_LOW, /*当年累计放电电量 KWh*/ BMS_RESVER_ACCUMULATED_CHARGE_CAPACITY_HIGH, /*累计充电容量 AH*/ BMS_RESVER_ACCUMULATED_CHARGE_CAPACITY_LOW, /*累计充电容量 AH*/ BMS_RESVER_ACCUMULATED_DISCHARGE_CAPACITY_HIGH, /*累计放电容量 AH*/ BMS_RESVER_ACCUMULATED_DISCHARGE_CAPACITY_LOW, /*累计放电容量 AH*/ BMS_RESVER_RELAY_OFF_REASON, /*接触器断开原因*/ BMS_RESVER_SAFETY_SUMMARY_HIGH, /*功能安全概要故障bit16~bit31*/ BMS_RESVER_CURRENT_LIMIT_REASON, /*限流原因*/ BMS_RESVER_OTHER_CRITICAL_INFO_2, /*其他故障告警II（Critical）*/ BMS_RESVER_OTHER_WARN_INFO_2, /*其他故障告警II（Warn）*/ BMS_RESVER_SERIOUS_ALARM_STATE, /*断电保护故障*/ BMS_RESVER_EXTERN_RESET_ALARM_1, /* 对外复归告警1 */ BMS_RESVER_EXTERN_RESET_ALARM_2, /* 对外复归告警2 */ BMS_RESVER_SYSTEM_POWER, /* 系统功率 */ BMS_RESVER_INNER_SOH, /* 内部SOH */ BMS_RESVER_INNER_SOE, /* 内部SOE */ BMS_RESVER_INFO_SUBOBJ_ID_BUTT } BMS_RESERVE_INFO_SUBOBJ_ID_ENUM;/*预留信息*/ typedef enum { BMS_RESVER_3_THERMAL_RUNAWAY_STATE = 0x0BC0, /*热失控触发信号*/ BMS_RESVER_3_THERMAL_RUNAWAY_HALT_BAT_NUM, /*热失控时电池编号*/ BMS_RESVER_3_ALARM_DTC_NEWEST_INDEX, /*告警类DTC索引*/ BMS_RESVER_3_EVENT_DTC_NEWEST_INDEX, /*事件类DTC索引*/ BMS_RESVER_3_CHARGE_LIMITING_RATIO, /*充电限流比率*/ BMS_RESVER_3_DISCHARGE_LIMITING_RATIO, /*放电限流比率*/ BMS_RESVER_3_EXT_STOP_INFO_2, /*对外停机2*/ BMS_RESVER_3_EXT_ALARM_INFO_2, /*对外告警2*/ BMS_RESVER_3_EXT_ALERT_INFO_2, /*对外预告警2*/ BMS_RESVER_3_GROUP_ACTIVE_TEST_ERR_NUM, /*组间检测错误编号*/ BMS_RESVER_3_INFO_SUBOBJ_ID_BUTT }BMS_RESERVE_INFO_3_SUBOBJ_ID_ENUM; typedef enum { BMS_RESVER_CFG_PARA_CHIP1_BATTERY_COUNT = 0xA40, /*采样芯片1单体数量*/ BMS_RESVER_CFG_PARA_CHIP2_BATTERY_COUNT, /*采样芯片2单体数量*/ BMS_RESVER_CFG_PARA_CHIP3_BATTERY_COUNT, /*采样芯片3单体数量*/ BMS_RESVER_CFG_PARA_CHIP4_BATTERY_COUNT, /*采样芯片4单体数量*/ BMS_RESVER_CFG_PARA_CHIP5_BATTERY_COUNT, /*采样芯片5单体数量*/ BMS_RESVER_CFG_PARA_COPPER_BIT1, /*铜牌位置配置1*/ BMS_RESVER_CFG_PARA_COPPER_BIT2, /*铜牌位置配置2*/ BMS_RESVER_CFG_PARA_COPPER_BIT3, /*铜牌位置配置3*/ BMS_RESVER_CFG_PARA_COPPER_BIT4, /*铜牌位置配置4*/ BMS_RESVER_CFG_PARA_TEMP_INDICATE_BIT1, /*温度位置配置1*/ BMS_RESVER_CFG_PARA_TEMP_INDICATE_BIT2, /*温度位置配置2*/ BMS_RESVER_CFG_PARA_TEMP_INDICATE_BIT3, /*温度位置配置3*/ BMS_RESVER_CFG_PARA_TEMP_INDICATE_BIT4, /*温度位置配置4*/ BMS_RESVER_CFG_PARA_TEMP_INDICATE_BIT5, /*温度位置配置5*/ BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_CRITICAL, /*模块电压过高告警阈值*/ BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_ALARM, BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_WARN, BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_CRITICAL, /*模块电压过低告警阈值*/ BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_ALARM, BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_WARN, BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_CRITICAL_RECOVER, /*模块电压过高恢复阈值*/ BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_ALARM_RECOVER, BMS_RESVER_CFG_PARA_PACK_VOL_OVER_HIGH_WARN_RECOVER, BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_CRITICAL_RECOVER, /*模块电压过低恢复阈值*/ BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_ALARM_RECOVER, BMS_RESVER_CFG_PARA_PACK_VOL_LOWER_LOW_WARN_RECOVER, BMS_RESVER_CFG_PARA_MAIN_INIT_STATE, /*主控初始化完成状态*/ BMS_RESVER_CFG_PARA_SIMULATION_TEST_INDEX, /*模拟测试数据ID*/ BMS_RESVER_CFG_PARA_SIMULATION_TEST_VALUE, /*模拟数据*/ BMS_RESVER_CFG_PARA_BANK_NUM, /*堆编号：DB中从1起*/ BMS_RESVER_CFG_PARA_IP_OFFSET, /*IP偏移*/ BMS_RESVER_CFG_PARA_IP_LAST_BYTE, /*IP最后一个字节*/ BMS_RESVER_CFG_PARA_TOTAL_BAT_OVER_VOL_SERIOUS, /*四级告警阈值*/ BMS_RESVER_CFG_PARA_TOTAL_BAT_LOWER_VOL_SERIOUS, BMS_RESVER_CFG_PARA_INSULATION_RESISTANCE_LOWER_SERIOUS, BMS_RESVER_CFG_PARA_SINGLE_BAT_OVER_VOL_SERIOUS, BMS_RESVER_CFG_PARA_SINGLE_BAT_LOWER_VOL_SERIOUS, BMS_RESVER_CFG_PARA_BAT_TEMP_OVER_SERIOUS, BMS_RESVER_CFG_PARA_BAT_CHARGE_TEMP_OVER_SERIOUS, BMS_RESVER_CFG_PARA_TOTAL_BAT_OVER_VOL_SERIOUS_RECOVER, /*四级告警恢复阈值*/ BMS_RESVER_CFG_PARA_TOTAL_BAT_LOWER_VOL_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_INSULATION_RESISTANCE_LOWER_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_SINGLE_BAT_OVER_VOL_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_SINGLE_BAT_LOWER_VOL_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_BAT_TEMP_OVER_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_BAT_CHARGE_TEMP_OVER_SERIOUS_RECOVER, BMS_RESVER_CFG_PARA_IP_THIRD_BYTE, /*IP第三个字节*/ BMS_RESVER_CFG_PARA_IP_SECOND_BYTE, /*IP第二个字节*/ BMS_RESVER_CFG_PARA_IP_FIRST_BYTE, /*IP第一个字节*/ BMS_RESVER_CFG_PARA_GATEWAY_FIRST_BYTE, /*网关第一个字节*/ BMS_RESVER_CFG_PARA_GATEWAY_SECOND_BYTE, /*网关第二个字节*/ BMS_RESVER_CFG_PARA_GATEWAY_THIRD_BYTE, /*网关第三个字节*/ BMS_RESVER_CFG_PARA_GATEWAY_LAST_BYTE, /*网关第四个字节*/ BMS_RESVER_CFG_PARA_SUBNETMASK_FIRST_BYTE, /*子网掩码第一个字节*/ BMS_RESVER_CFG_PARA_SUBNETMASK_SECOND_BYTE, /*子网掩码第二个字节*/ BMS_RESVER_CFG_PARA_SUBNETMASK_THIRD_BYTE, /*子网掩码第三个字节*/ BMS_RESVER_CFG_PARA_SUBNETMASK_LAST_BYTE, /*子网掩码第四个字节*/ BMS_RESVER_CFG_PARA_SYS_TIME_ZONE, /*系统时区*/ BMS_RESVER_CFG_PARA_CURRENT_RANGE_MAIN_TYPE, /*电流主类型量程*/ BMS_RESVER_CFG_PARA_CURRENT_RANGE_SUB_TYPE, /*电流副类型量程*/ BMS_RESVER_CFG_PARA_NETWORK_NTP_IP_1, /*NTP IP 第一个字节*/ BMS_RESVER_CFG_PARA_NETWORK_NTP_IP_2, /*NTP IP 第二个字节*/ BMS_RESVER_CFG_PARA_NETWORK_NTP_IP_3, /*NTP IP 第三个字节*/ BMS_RESVER_CFG_PARA_NETWORK_NTP_IP_4, /*NTP IP 第四个字节*/ BMS_FORCE_SOC_START_FOLLOW_SMOOTH, /* 总控下发SOC */ BMS_FORCE_SYN_TICK, /* 同步信息tick */ BMS_FORCE_QUERY_FINASH_FALG, /* 查询完成标志 */ BMS_FORCE_PRODUCTION_TEST_MODE, /* 生产测试模式配置*/ BMS_FORCE_HEART_BEAT, /* 总控配置的心跳帧 */ BMS_FORCE_OCV_STANDY_TIME, /* OCV静置时间配置 */ BMS_FORCE_OCV_INTERVAL_TIME, /* OCV间隔时间配置 */ BMS_FORCE_BANK_CURRENT_STATE, /* 堆电流状态 */ BMS_FORCE_USE_DISPLAYSOH_CAL_CAPATICY, /* 使用外部SOH计算总容量*/ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_CRITICAL_LIMIT, /* 模组压差过高保护阈值 */ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_ALARM_LIMIT, /* 模组压差过高告警阈值 */ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_WARN_LIMIT, /* 模组压差过高预告警阈值 */ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_CRITICAL_RECOVER_LIMIT, /* 模组压差过高保护恢复阈值 */ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_ALARM_RECOVER_LIMIT, /* 模组压差过高告警恢复阈值 */ BMS_FORCE_PACK_VOL_DIFF_OVER_HIGH_WARN_RECOVER_LIMIT, /* 模组压差过高预告警恢复阈值 */ BMS_FORCE_MAX_CHG_POWER_THROLD, /* 最大充电功率阈值（无总控时使用） */ BMS_FORCE_MAX_DISCHG_POWER_THROLD, /* 最大放电功率阈值（无总控时使用） */ BMS_FORCE_CHIP6_BATTERY_COUNT, /* 采样芯片6单体数量*/ BMS_FORCE_CHIP7_BATTERY_COUNT, /* 采样芯片7单体数量*/ BMS_FORCE_CHIP8_BATTERY_COUNT, /* 采样芯片8单体数量*/ BMS_FORCE_COPPER_BIT5, /* 铜牌位置配置5*/ BMS_FORCE_COPPER_BIT6, /* 铜牌位置配置6*/ BMS_FORCE_COPPER_BIT7, /* 铜牌位置配置7*/ BMS_FORCE_COPPER_BIT8, /* 铜牌位置配置8*/ BMS_RESVER_CFG_SUBOBJ_ID_BUTT } BMS_RESERVE_CFG_SUBOBJ_ID_ENUM;/*预留配置信息*/ /* -------------------------------主控版本信息DB-------------------------- */ typedef enum { BMS_VERSION_SOFTWARE_PROJECT_NUM = 0x01C0, /*软件项目编号*/ BMS_VERSION_SOFTWARE_MAIN_VERSION, /*软件主版本号*/ BMS_VERSION_SOFTWARE_SUB_VERSION, /*软件子版本号*/ BMS_VERSION_SOFTWARE_CORRECT_VERSION, /*软件修正版本号*/ BMS_VERSION_HARDWARE_TYPE, /*硬件类型*/ BMS_VERSION_HARDWARE_MAIN_VERSION, /*硬件主版本号*/ BMS_VERSION_HARDWARE_SUB_VERSION, /*硬件子版本号*/ BMS_VERSION_CANRBUS_PROTOCOL_VERSION, /*canrbus协议版本号*/ BMS_VERSION_J1939_PROTOCOL_VERSION, /*j1939协议版本号*/ BMS_VERSION_BOOT_MAIN_VERSION, /*BOOTLOADER主版本号*/ BMS_VERSION_BOOT_SUB_VERSION, /*BOOTLOADER子版本号*/ BMS_VERSION_BOOT_CORRECT_VERSION, /*BOOTLOADER修正版本号*/ BMS_VERSION_DB_VERSION, /* bit15-bit12主版本 bit11-bit8子版本 Bit7-bit0修正版本 */ WARN_MAX_VOL_BATTERY_NUM, /*报警时最高电压电池编号*/ WARN_MAX_VOL_BATTERY_VAULE, /*报警时最高电压值*/ STOP_MAX_VOL_BATTERY_NUM, /*停机时最高电压电池编号*/ STOP_MAX_VOL_BATTERY_VAULE, /*停机时最高电压值*/ WARN_MIN_VOL_BATTERY_NUM, /*报警时最低电压电池编号*/ WARN_MIN_VOL_BATTERY_VAULE, /*报警时最低电压值*/ STOP_MIN_VOL_BATTERY_NUM, /*停机时最低电压电池编号*/ STOP_MIN_VOL_BATTERY_VAULE, /*停机时最低电压值*/ WARN_BAT_GROUP_OVER_VOL_VAULE, /*电池组过压报警时电压值*/ STOP_BAT_GROUP_OVER_VOL_VAULE, /*电池组过压停机时电压值*/ WARN_BAT_GROUP_LOW_VOL_VAULE, /*电池组欠压报警时电压值*/ STOP_BAT_GROUP_LOW_VOL_VAULE, /*电池组欠压停机时电压值*/ WARN_CHARGE_OVER_CURRENT_VAULE, /*电池充电过流报警时电流值*/ STOP_CHARGE_OVER_CURRENT_VAULE, /*电池充电过流停机时电流值*/ WARN_DISCHARGE_OVER_CURRENT_VAULE, /*电池放电过流报警时电流值*/ STOP_DISCHARGE_OVER_CURRENT_VAULE, /*电池放电过流停机时电流值*/ WARN_MAX_TEMP_BATTERY_NUM, /*报警时最高电池温度点编号*/ WARN_MAX_TEMP_BATTERY_VAULE, /*报警时最高电池温度值*/ STOP_MAX_TEMP_BATTERY_NUM, /*停机时最高电池温度点编号*/ STOP_MAX_TEMP_BATTERY_VAULE, /*停机时最高电池温度值*/ WARN_MIN_TEMP_BATTERY_NUM, /*报警时最低电池温度点编号*/ WARN_MIN_TEMP_BATTERY_VAULE, /*报警时最低电池温度值*/ STOP_MIN_TEMP_BATTERY_NUM, /*停机时最低电池温度点编号*/ STOP_MIN_TEMP_BATTERY_VAULE, /*停机时最低电池温度值*/ WARN_MAX_PACK_TEMP_VALUE, STOP_MAX_PACK_TEMP_VALUE, WARN_MAX_TEMP_RISE_BATTERY_NUM, WARN_MAX_TEMP_RISE_VALUE, STOP_MAX_TEMP_RISE_BATTERY_NUM, STOP_MAX_TEMP_RISE_VALUE, WARN_MAX_POLARITY_TEMP_BATTERY_NUM, /*报警时最高功率温度点编号(极柱温度)*/ WARN_MAX_POLARITY_TEMP_BATTERY_VAULE, /*报警时最高功率温度值(极柱温度)*/ STOP_MAX_POLARITY_TEMP_BATTERY_NUM, /*停机时最高功率温度点编号(极柱温度)*/ STOP_MAX_POLARITY_TEMP_BATTERY_VAULE, /*停机时最高功率温度值(极柱温度)*/ WARN_OVER_SINGLE_VOL_BATTERY_VALUE, /*电池单体电压最高最低之间压差过大告警时压差值*/ STOP_OVER_SINGLE_VOL_BATTERY_VALUE, /*电池单体电压最高最低之间压差过大停机时压差值*/ WARN_LOW_INSULATION_RESISTANCE_VALUE, /*绝缘电阻过小告警时阻值*/ STOP_LOW_INSULATION_RESISTANCE_VALUE, /*绝缘电阻过小停机时阻值*/ WARN_OVER_TOTAL_VOL_BATTERY_VALUE, /*总电压和从控总电压压差过大告警时差值(单位:0.1V)*/ STOP_OVER_TOTAL_VOL_BATTERY_VALUE, /*总电压和从控总电压压差过大停机时差值(单位:0.1V)*/ WARN_OVER_SINGLE_TMPR_BATTERY_VALUE, /*电池单体温度最高最低之间温差过大告警时压差值*/ STOP_OVER_SINGLE_TMPR_BATTERY_VALUE, /*电池单体温度最高最低之间温差过大停机时压差值*/ WARN_MAX_PACK_VOL_OVER_HIGH_NUM, /*告警时最高模组电压编号*/ WARN_MAX_PACK_VOL_OVER_HIGH_VALUE, /*模组电压过高告警时电压值*/ STOP_MAX_PACK_VOL_OVER_HIGH_NUM, /*停机时最高模组电压编号*/ STOP_MAX_PACK_VOL_OVER_HIGH_VALUE, /*模组电压过高停机时电压值*/ WARN_MIN_PACK_VOL_LOWER_LOW_NUM, /*告警时最低模组电压编号*/ WARN_MIN_PACK_VOL_LOWER_LOW_VALUE, /*模组电压过低告警时电压值*/ STOP_MIN_PACK_VOL_LOWER_LOW_NUM, /*停机时最低模组电压编号*/ STOP_MIN_PACK_VOL_LOWER_LOW_VALUE, /*模组电压过低停机时电压值*/ BMS_VERSION_INFO_SUBOBJ_ID_BUTT } BMS_VERSION_INFO_SUBOBJ_ID_ENUM; /************************************** 项目专用DB地址 ************************************/ // INFO 0xB00 ~ 0xB3F typedef enum { BMS_PROJECT_INFO_CASE1 = 0xB00, BMS_PROJECT_INFO_SUBOBJ_ID_BUTT = 0xB3F + 1 } BMS_PROJECT_INFO_SUBOBJ_ID_ENUM; // CFG 0xB40 ~ 0xB7F typedef enum { BMS_PROJECT_CFG_CASE1 = 0xB40, BMS_PROJECT_CFG_SUBOBJ_ID_BUTT = 0xB7F + 1 } BMS_PROJECT_CFG_SUBOBJ_ID_ENUM; /************************************** 项目专用DB地址 ************************************/ /* -------------------------------主控详细信息数量-------------------------- */ #define MAX_BATTERY_NUM_IN_ONE_CLUSTER 512 /* 最大簇电池数量 */ #define MAX_BAT_TEMPERATURE_NUM_IN_ONE_CLUSTER 512 /* 最大单簇电池温度数量 */ #define MAX_BAT_TEMP_RISE_NUM_IN_ONE_CLUSTER 0 /* 最大单簇电池温升信息数量 */ #define RESISTANCE_NUM_IN_ONE_CLUSTER 512 /* 单簇单体内阻数量，若使能单体内阻计算，和单体数一致即可 */ #define PASSIVE_TEMP_NUM_IN_ONE_CLUSTER 80 /* 单簇被动均衡温度数量，一般是一个采样芯片一个被动均衡温度 */ #define ACTIVE_TEMP_NUM_IN_ONE_CLUSTER 80 /* 单簇主动均衡温度数量，一般是一个采样芯片一个主动均衡温度 */ #define ANODE_TEMP_NUM_IN_ONE_CLUSTER 128 /* 单簇正极柱温度数量，0或者一个从控一个正极柱温度 */ #define CATHODE_TEMP_NUM_IN_ONE_CLUSTER 128 /* 单簇负极柱温度数量，0或者一个从控一个负极柱温度*/ #define MAX_PACK_NUM_IN_ONE_CLUSTER 64 /* 最大单簇模组电压数量*/ /* -------------------------------主控详细信息DB-------------------------- */ #define BMS_BAT_TEMP_SUBOBJ_ID_1 (0x0200) /*电池温度*/ #define BMS_VOLTAGE_SUBOBJ_ID_1 (0x0400) /*单体电压*/ #define BMS_RESISTANCE_SUBOBJ_ID_1 (0x600) /*单体内阻*/ #define BMS_PASSIVE_TEMP_SUBOBJ_ID_1 (0x0800) /*被动均衡温度信息*/ #define BMS_ACTIVE_TEMP_SUBOBJ_ID_1 (0x0880) /*主动均衡温度信息*/ #define BMS_ANODE_TEMP_SUBOBJ_ID_1 (0x0900) /*正极柱温度*/ #define BMS_CATHODE_TEMP_SUBOBJ_ID_1 (0x0980) /*负极柱温度*/ #define BMS_BAT_TEMP_RISE_SUBOBJ_ID_1 (0) /*电池温升信息*/ #define BMS_BAT_BALANCE_STATUS_SUBOBJ_ID_1 (0) /*均衡状态信息*/ #define BMS_PACK_VOL_SUBOBJ_ID_1 (0) /*电池包总压信息*/ #define BMS_SOH_SUBOBJ_ID_1 (0xB2C8) /*单体SOH*/ #define BMS_SOC_SUBOBJ_ID_1 (0xBA98) /*单体SOC*/ #endif